Sinumerik CNC Training Software Siemens SinuTrain Free Download. Sinumerik CNC Training Software Siemens SinuTrain Free Download. The SinuTrain software can be installed on Windows 7. Siemens provides free to download manuals for Sinumerik CNC controls. Siemens Industry, Inc. Motion Control Business — Machine Tools. Temario oposiciones auxiliar enfermeria pdf to doc. 390 Kent Avenue. Elk Grove Village, IL 60007. Your machine tool going. Provides unparalleled potential for turning and milling workpieces more productively. With ShopMill/ShopTurn sequence programming, the SINUMERIK 828D boasts the most straightforward CNC program editor in. Once again - the manual is nigh worthless in any amount of details as to how to program this canned cycle. Just got in some 1/8 NPTF mills from Carl and tried to make parts, but the mills won't make it in one pass, and was busting them up. Carl says 3 pass at 50%, 35%, and 15% clean-up. 'I think I can make that happen.' But my efforts were futile. I put a call into Siemens this AM, but not gotten a call back yet. This code here does make 2 passes, but I cannot qualify (without going back and watching the CRT) how much it took either time, but I am expecting it to make 3 passes, but it is only 2. Anyone out there running Shopmill and have a good handle on the ins/outs of this canned cycle? I originally had this set to.017/pass expecting.017,.013, and.005 ------------------------------ Think Snow Eh! Have not figgered out why the canned cycle didn't work like I expected yet, but by calling it 3 times - I get the control that I expect. Prolly costs me 5 extra seconds on a 5 minute cycle, so - no worries on this part anyhow. However - that did NOT fix my issues. It turns out that the control was trumping my M3, and spinning the tool bass akwards. That is what I thought that the tool looked like right outta the gate, and the spindle was acting a little funny at times, but I must'a checked the direction with my fingers a half dozen times prior, but it was always going CW when I checked. But then I touched it just as it was entering the hole (feed hold) and it was in fact going the other direction! It was the canned cycle that did it to me. The canned cycle reads a field in the OFFSET page that had that tool labeled as CCW* for whatever reason. I switched it to non-directional, and it didn't like that either, and threw a hissy. So then I had to tell it that it was a CW tool. Milled prolly 70 holes since then - looking good! But what gets me is that the first two holes on each tool were good, and then it would die and make ratty threads. We ran a while with the buggered tools to at least keep running, and so I have to go back and clean up some parts with a good tap now. The first few parts that I made I tapped in the B-port to git them out the door quickly and the second part - I ripped the top 1/8' of threads right outta the hole! That is a std tap and 1026 DOM. So I just started the threads with that tap in the B-port and finished by hand with some other slight helical tap that I think is coated. Both taps - as well as the thread mill are dipped in oil before each use. Otherwise running dry. So - two main points: 1) It wasn't Carls mills that were too brittle, it was a control that was too smart (?) for my own good. ![]() 2) The mills prolly would have been fine with the 1 or maybe 2 passes had it been going the right direction. * CCW /= a 2 stroke motor manufacturer, nor ammo manufacturer. ---------------------- Think Snow Eh! It was the canned cycle that did it to me. The canned cycle reads a field in the OFFSET page that had that tool labeled as CCW* for whatever reason. I switched it to non-directional, and it didn't like that either, and threw a hissy. So then I had to tell it that it was a CW tool.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |